Most cited (updated monthly)

Because of its ultrahigh hardness, synthetic diamond has been widely used in advanced manufacturing and mechanical engineering. As an ultra-wide bandgap semiconductor, on the other hand, diamond recently shows a great potential in electronics industry due to its outstanding physical properties. However, like silicon-based electronics, the electrical properties of diamond should be well modulated before it can be practically used in electronic devices. In this work, we briefly review the recent progresses in producing high-quality, electronic grade synthetic diamonds, as well as several typical strategies, from the conventional element doping to the emerging “elastic strain engineering,” (ESE) for tuning the electrical and functional properties of microfabricated diamonds. We also briefly show some device application demonstrations of diamond and outline some remaining challenges that are impeding diamond’s further practical applications as functional devices and offer some perspective for future functional diamond development.

The dislocation identification method using X-ray topography by reflection mode geometry was applied to characterize IIa, Ib and highly B doped high pressure high temperature (HPHT) grown crystals. In both IIa and Ib crystals, dislocations are found to propagate in the <111> grown direction, with dominant vectors of [110] and [1-10], neither of which has no c-axis segment. For Ib crystal, many dislocations are also generated in the <112> and <121> directions, which are slightly tilted to <111>. It was confirmed that the dislocations in the same direction have the same Burgers vectors, but the dislocations are spread in broad area. A total of up to 20 HPHT crystals were measured and found to exhibit different dislocation distributions. This indicates an immature growth technique in terms of dislocation. Measurements of four chemical vapor deposition (CVD) substrates showed numerous dislocation bundles, making individual dislocation directions analysis impossible. CVD substrates suffer from an increase in dislocations due to CVD growth, resulting in poor diamond quality in terms of dislocation. XRT analysis on dislocations of epitaxial growth will be very important prior to CVD substrates analysis.

In recent years, there have been more and more researches on the surface modification of diamonds, however, the exact types and quantities of oxygen-related species on diamond surfaces and the method to control the condition parameters to obtain as many oxygen-containing groups as possible have been rarely studied so far. Therefore, in this work, we focused on these questions. And we find out that ozone oxidation would not affect the overall crystal structure and morphology of diamonds. Besides, changing oxidation time and ozone concentration would significantly influence the density of hydroxyl groups, which is manifested as a change of oxygen content. In order to make the hydroxyl density on diamond surface reach a high level (3.12 × 1014 units/cm2), so that diamonds can be better combined with the resin matrix, the ozone oxidation time should be 15 min, and the ozone concentration should be 115 g•m−3. And under these conditions, the thermal conductivity of diamond and polysiloxane composites can reach 8.02 W/mK.

This article describes key material science/technology issues to implement polycrystalline diamond scaffolds to enable processes for biological cells growth relevant for using cells grown in the laboratory for the treatment of human biological conditions. Issues investigated include

The irradiation effect of X-ray on the electrical properties of Schottky-barrier diode (SBD) and metal-semiconductor field-effect transistors (MESFET) based on the surface conductivity of hydrogen-terminated single-crystal diamond (SCD) epilayers was investigated. The Ohmic contact was formed by a Pd/Ti/Au multilayer and the Schottky metal was Al thin film for the fabrication of the diamond SBDs and MESFETs. The X-ray irradiation was performed with a dose of 100 kGy. It was observed that both the forward current of the SBDs and the drain current of the MESFETs experienced a reduction after the X-ray irradiation. The type of the single-crystal diamond substrate had an obvious effect on the radiation properties. For the MESFETs on the type-Ib SCD substrate, the variation of the drain currents as the irradiation was inhomogeneous across the devices. For the MESFETs on the type-IIa SCD substrate, the reduction of the drain currents is more uniform and the threshold voltage changed little upon X-ray irradiation. The partial oxidation in the air of the exposure area in the device and the edge of the Al gate may be responsible for the degradation of the device performance under X-ray irradiation. The passivation technique with radiation-robustness is needed for diamond devices based on the surface conductivity of diamond.

Ferri/ferro-cyanide ([Fe(CN)6]3−/4−) redox couple has been extensively used as a benchmark to assess electrocatalytic degradation capability of boron-doped diamond (BDD) electrodes. However, the [Fe(CN)6]3−/4− is far more sensitive to the surface terminal groups of BDD surface than the other factors (e.g. surface morphology and electrode configuration) that are closely related to electrocatalytic degradation properties. Thus, inconsistency exists while correlating the degradation properties of BDD with electrochemical properties determined from ferri/ferro-cyanide redox couple. Herein, an exemplar pollutant, reactive blue 19 (RB-19), was electrochemically degraded using various terminated BDD electrodes, including hydrogen-terminated (H-BDD), oxygen-terminated (O-BDD) and porous oxygen-terminated BDDs (OE-BDD), obtained via cathodic and anodic polarization as well as oxygen plasma etching, respectively. Surprisingly, OE-BDD with the lower heterogeneous electron transfer rate constant for [Fe(CN)6]3−/4− showed a better electrocatalytic degradation capability toward RB-19, indicating the inconsistency for qualitatively evaluating degradation properties according to the kinetic parameters extracted from [Fe(CN)6]3−/4− redox system.

Semiconductor devices generally take advantage of the charge of electrons, whereas magnetic materials are used for recording information involving electron spin. To make use of both charge and spin of electrons in semiconductors, a high concentration of magnetic elements can be introduced in nonmagnetic III-V semiconductors to make magnetic semiconductor. In this work, Fe-Diamond was obtained with low solubility by modified microwave plasma chemical vapor deposition technique. Magnetic measurements revealed that the magnetic transition temperature from paramagnetic to ferromagnetic-like is above room temperature. The bandgap of Fe-Diamond is calculated to be 1.65 eV, which indicates that Fe-Diamond is a room temperature diluted ferromagnetic semiconductor.